No significant differences in wound healing were observed between PLA and PLA/PVA/SA fiber membranes in our study. Furthermore, Masson staining and PCR displayed the PLA fiber membrane promoted protein deposition compared to the PLA/PVA/SA fiber membrane. In addition, IHC suggested that PLA/PVA/SA dressing reduced the inflammatory response during early wound healing compared to the PLA fiber membrane. These findings highlight the utility of fiber membranes as novel wound-healing dressings.Cancer is a major health concern and the prognosis is often poor. Significant advances in nanotechnology are now driving a revolution in cancer detection and treatment. The goal of this study was to develop a novel hybrid nanosystem for melanoma treatment, integrating therapeutic and magnetic targeting modalities. Hence, we designed long circulating and pH-sensitive liposomes loading both dichloro(1,10-phenanthroline) copper (II) (Cuphen), a cytotoxic metallodrug, and iron oxide nanoparticles (IONPs). The synthetized IONPs were characterized by transmission electron microscopy and dynamic light scattering. Lipid-based nanoformulations were prepared by the dehydration rehydration method, followed by an extrusion step for reducing and homogenizing the mean size. Liposomes were characterized in terms of incorporation parameters and mean size. High Cuphen loadings were obtained and the presence of IONPs slightly reduced Cuphen incorporation parameters. Cuphen antiproliferative properties were preserved after association to liposomes and IONPs (at 2 mg/mL) did not interfere on cellular proliferation of murine and human melanoma cell lines. Moreover, the developed nanoformulations displayed magnetic properties. The absence of hemolytic activity for formulations under study demonstrated their safety for parenteral administration. In conclusion, a lipid-based nanosystem loading the cytotoxic metallodrug, Cuphen, and displaying magnetic properties was successfully designed.Cholesteryl ester liquid crystals exhibit thermochromic properties related to the existence of a twisted nematic phase. We formulate ternary mixtures of cholesteryl benzoate (CB), cholesteryl pelargonate (CP), and cholesteryl oleyl carbonate (COC) to achieve thermochromic behavior. We aim to achieve thermochromic fibers by incorporating the liquid crystal formulations into electrospun fibers. Two methods of incorporating the liquid crystal (LC) are compared (1) blend electrospinning and (2) coaxial electrospinning using the same solvent system for the liquid crystal. For blend electrospinning, intermolecular interactions seem to be important in facilitating fiber formation since addition of LC can suppress bead formation. Coaxial electrospinning produces fibers with higher nominal fiber production rates (g/hr) and with higher nominal LC content in the fiber (wt. LC/wt. polymer assuming all of the solvent evaporates) but larger fiber size distributions as quantified by the coefficient of variation in fiber diameter than blend electrospinning with a single nozzle. Importantly, our proof-of-concept experiments demonstrate that coaxially electrospinning with LC and solvent in the core preserves the thermochromic properties of the LC so that thermochromic fibers are achieved.In the present work, ten data mining algorithms have been used to generate models capable of predicting the surface roughness of parts printed on polylactic acid (PLA) by using fused deposition modeling (FDM). The models have been trained using experimental data measured on 27 horizontal (XY) and 27 vertical (XZ) specimens, printed using different values for the parameters studied (layer height, extrusion temperature, print speed, print acceleration and flow). The models generated by multilayer perceptron (MLP) and logistic model trees (LMT) have obtained the best results in a cross-validation. Although it does not obtain such optimal results, the J48 algorithm (C4.5) allows the generation of models in the form of a decision tree. These trees permit to determine which print parameters have an influence on the surface roughness. For XY specimens, the surface roughness measured in the direction parallel to the extrusion path (Ra,0,XY ) depends on the flow, the print temperature and the layer height; in the direction perpendicular to the extrusion path, the surface roughness (Ra,90,XY) depends only on the flow. For XZ specimens, the surface roughness measured in the direction parallel to the extrusion path (Ra,0,XZ) depends only on the print speed; in the direction perpendicular to the extrusion path (Ra,90,XZ), it depends on the layer height and the extrusion temperature. According to the study carried out, the most suitable set up provides values of Ra,0,XY, Ra,90,XY, Ra,0,XZ and Ra,90,XZ equal to 0.46, 1.18, 0.45 and 11.54, respectively. A practical application of this work is the manufacture of PLA frame glasses using FDM.The objective of this study is to compare the effect of selected operating factors on the mechanical properties of epoxy adhesive compounds aged in salt water. Five different water environments were tested tap water, normal seawater (reference salinity value), seawater with double reference salinity value, seawater with half of the reference salinity and seawater with a quarter of the reference salinity value. Samples of two different adhesive compounds were prepared using the epoxy resin and triethylenetetramine curing agent. One of the compounds was filled with calcium carbonate. The samples were aged in five different water environments for three months, one month and one week, respectively. Mechanical properties of the cured adhesive compound samples were determined via strength tests performed on the Zwick/Roell Z150 testing machine in compliance with the EN ISO 604 standard. DL-AP5 in vivo The objective of the experiments was to determine the effect of different seawater environments on selected mechanical properties (including strength) of the fabricated adhesive compounds.Polymer scaffolds constitute a very interesting strategy for tissue engineering. Even though they are generally non-toxic, in some cases, they may not provide suitable support for cell adhesion, proliferation, and differentiation, which decelerates tissue regeneration. To improve biological properties, scaffolds are frequently enriched with bioactive molecules, inter alia extracellular matrix proteins, adhesive peptides, growth factors, hormones, and cytokines. Although there are many papers describing synthesis and properties of polymer scaffolds enriched with proteins or peptides, few reviews comprehensively summarize these bioactive molecules. Thus, this review presents the current knowledge about the most important proteins and peptides used for modification of polymer scaffolds for tissue engineering. This paper also describes the influence of addition of proteins and peptides on physicochemical, mechanical, and biological properties of polymer scaffolds. Moreover, this article sums up the major applications of some biodegradable natural and synthetic polymer scaffolds modified with proteins and peptides, which have been developed within the past five years.