The lack of a PDL, which acts as an energy absorber, is a contributor to implants’ early failure; however, these discrepancies are not well understood because of limited in vivo research. This study investigated the discrepancy in biomechanical behaviors between natural teeth and dental implants by detecting micro-movements in vivo.

We designed a device that could measure precisely mechanical behaviors such as creep, stress relaxation, and hysteresis by using load-control displacement on teeth and implants. We also compared energy dissipation between natural teeth and dental implants by subtracting the area of the hysteresis loop of natural teeth from that of dental implants.

Biphasic curves with an initial phase of rapid response and a subsequent phase of slow response were confirmed in creep and stress relaxation curves for the load-time relationship in natural teeth. By contrast, the behavior of creep or stress relaxation was less prominent when the dental implants were tested. We observed that the periodontal ligament under an axial intrusive load of 300g in a loading rate 3g/s could dissipate the energy of 7.35±1.18×10

mJ, approximately 50 times that of the dental implants (1.47±1.22×10

) with statistically significant (p<0.05).

We confirmed natural teeth could achieve greater energy dissipation compared to dental implants, which owe to that natural teeth exhibited fluid and viscoelastic properties.

We confirmed natural teeth could achieve greater energy dissipation compared to dental implants, which owe to that natural teeth exhibited fluid and viscoelastic properties.

The objective of this study was to evaluate the combined effect of the sulfuric acid etching and an acidic adhesive conditioning on the shear bond strength of PEEK to a resin-matrix composite.

Forty PEEK specimens were assigned randomly to 4 groups for H

SO

etching followed by universal adhesive (pH at 2.5) conditioning for 0, 1, 3, and 5 min. Thirty PEEK specimens were divided into 3 groups for only acidic adhesive conditioning for 0, 1, 3, and 5 min. After the light-curing of the adhesive, a nanohybrid resin composite was applied onto the surfaces and then light-cured following the manufacturer`s guidelines. All specimens were stored in distilled water at 37 °C for 24 h mechanical testing. Shear bond strength tests were performed using a universal testing machine. Surfaces were analyzed by SEM, light interferometry, FTIR, and liquid contact angle measurement. Statistical analysis was performed by one-way ANOVA and Tukey’s post hoc tests (p < 0.05).

No adhesion was achieved between untreated PEEK a resin-matrix composite, regardless of the adhesive conditioning time points. Shear bond strength of H

SO

-etched PEEK to resin-matrix composite increased with time (0 mmin. 4.95 ± 2.86 MPa < 1 min 9.35 ± 2.26 MPa < 3 min 17.84 ± 2.82 MPa < 5 min 21.43 ± 5.00 MPa). SEM images revealed a significant modification of PEEK surface topography after the H

SO

etching.

The acidic adhesive was unable to modify the untreated PEEK surface to establish an effective adhesion although a synergistic effect was noticed when the universal (acidic) adhesive was applied over a H

SO

-etched PEEK surface, thus improving the PEEK to resin-matrix composite adhesion.

The acidic adhesive was unable to modify the untreated PEEK surface to establish an effective adhesion although a synergistic effect was noticed when the universal (acidic) adhesive was applied over a H2SO4-etched PEEK surface, thus improving the PEEK to resin-matrix composite adhesion.

The effects of reduced chewing loads on load bearing integrity of interradicular bone (IB) within dentoalveolar joints (DAJ) in rats were investigated.

Four-week-old Sprague Dawley rats (N = 60) were divided into two groups; rats were either fed normal food, which is hard-pellet food (HF) (N = 30), or soft-powdered chow (SF) (N = 30). Biomechanical testing of intact DAJs and mapping of the resulting mechanical strains within IBs from 8- through 24-week-old rats fed HF or SF were performed. Tension- and compression-based mechanical strain profiles were mapped by correlating digital volumes of IBs at no load with the same IBs under load. Heterogeneity within IB was identified by mapping cement lines and TRAP-positive multinucleated cells using histology, and mechanical properties using nanoindentation technique.

Significantly decreased interradicular functional space, IB volume fraction, and elastic modulus of IB in the SF group compared with the HF group were observed, and these trends varied with an incynamic DAJ.High-yielding dairy cows are often fed high proportions of cereal grain and pulses. For several reasons, it would be desirable to replace these feed sources with forage, which is not suitable for human consumption. Feeding large amounts of forage to dairy cows could also make dairy production more publicly acceptable in the future. In this study, we estimated genetic parameters for total dry matter intake (DMI), DMI from forage (DMIFor), energy-corrected milk (ECM), and ECM produced from forage (ECMFor). A total of 1,177 lactations from 575 cows of Swedish Red (SR) and Holstein (HOL) dairy breeds were included in the study. Mixed linear animal random regression models were used, with fixed effect of calving season and lactation week nested within parity 1 and 2+, fixed effect of calving year, and random regression coefficients for breeding value (up to linear) and permanent environmental effect (up to quadratic) of the cow. ML265 chemical structure Heritability for DMI and DMIFor was generally higher for HOL than for SR in all-parityh; the lowest value was for DMI in HOL at 0.81. The genetic correlation between parities was rather high in the first part of the lactation. During the first 8 wk, the correlation was lower for HOL than for SR, except for ECM. We found that DMIFor and ECMFor showed reasonably large heritability, and future work should explore the possibility of genomic evaluations.The objective of this study was to investigate the short- and long-term effects of different feed presentations on feed sorting and rumen pH in weaned calves. Thirty-six weaned female calves at the age of 12 wk (78 d) were raised in pairs (18 pens; n = 6/treatment) and randomly exposed to 1 of 3 feed presentation treatments (1) concentrate ration (CON, only exposed to concentrate); (2) separate ration (CH, exposed to concentrate and hay as separate components); and (3) mixed ration (Mix, exposed to a mixed diet containing 75% concentrate and 25% hay). After 4 wk (from d 78 to 105) on different feed presentations, all weaned calves were introduced to a novel total mixed ration (TMR) for another 12 wk (from d 106 to 189). Fresh feed and orts were sampled daily before (wk 12 to 15) and after (wk 16, 17, and 28) transitioning to a TMR diet for analysis of feed sorting. Rumen fluid was sampled in wk 12, 13, 15, 16, 17, and 28 to determine rumen pH. The performance of weaned calves was affected by the different feed presentations during the pre-changing period, such that calves fed CON had a lower dry matter intake (DMI) and average daily gain than calves fed CH and Mix diets.