The incidence risks of SARA and SCK were 23.3% and 46.2%, respectively. Simultaneous occurrence of SCK and SARA (SCASCK) was present in 5.2% of the cows. In the final multivariable model, the occurrence of SARA (Odds Ratio OR = 39.4), SCK (OR = 47.4) and SCASCK (OR = 68.5) was associated with increased odds of PA. Feeding a transition period diet was associated with reduced odds of PA (OR = 0.15). Second parity cows had significantly lower odds of PA than first parity cows (OR = 0.21). In conclusion, inadequate pre-partum and postpartum nutritional management of the herds increased the occurrence of SARA and SCK, which had adverse effects on reproductive performance. © 2020 The Author(s).An alternative method of synthesizing ZnO-TiO2 nanorods is through route precipitation and sintering at 600 °C. In this study, the introduction of Ti into Zn in the molar ratio TiZn (13) produced a composite ZnO-Low TiO2 (ZnO-LTiO2) while 11 produced ZnO-High TiO2 (ZnO-HTiO2). The effect of the Ti introduced on the anti-bacterial properties of ZnO-TiO2 nanorods was investigated with the product structure characterized by XRD and the optimal intensity at 2θ 31.72°, 34.37°, 36.19° showed a Wurzite structure and a crystal size of 35.8-41.5 nm. The average pore diameters for ZnO-LTiO2 and ZnO-HTiO2 were around 5.159 nm and 6.828 nm while the surface areas were 15.692 m2/g and 15.421 m2/g respectively. The anti-bacterial textile fiber construction was prepared using dip-spin coating with the application of an adipic acid crosslinker for 6 h and stable coating up to 10 times washing. The improvement of Pseudomonas a eruginosa (Pa) antibacterial properties in the textiles with coating had an inhibition zone of 20.5-25.0 mm and 16.2 mm without the coating. The elements of the cotton fiber construction include C at 54.60%, O at 40.89%, Ti at 0.81% and Zn at 2.60% while the TG-DTA analysis conducted showed an increase in the heat stability of the textile fibers to a temperature of 400°C, after which the textiles were modified by coating ZnO-TiO2 nanorods. The findings of this research could be successfully applied to improve the antibacterial properties of textiles. © 2020 The Authors.Aim Dermatomyositis (DM) is an inflammatory myopathy in adults that is strongly associated with malignancy. The aim of this study was to evaluate whether whole-body 18F-FDG PET/CT imaging can offer a standard option searching for underlying malignancy in DM patients. Methods Seventy-five patients diagnosed with DM were referred to our department for whole-body 18F-FDG PET/CT to determine whether the patients suffered from malignant tumor. All PET images were analyzed by two experienced nuclear medicine physicians separately. Results According to the 18F-FDG PET/CT results, 19 patients were suspected to suffer from malignant tumor, then biopsy was performed. Of the 19 patients, 17 patients were confirmed to have malignant tumor. The pathological types were nasopharyngeal carcinoma, rectal cancer, lung cancer, colon cancer, gastric cancer, gallbladder cancer, kidney cancer, ovarian cancer, breast cancer, lymphoma and vertebral metastatic adenocarcinoma of unknown origin. No malignancy was found for the 56 PET-negative patients during follow-up. For the age between 17 patients with malignancy and 58 patients without malignancy, no significant difference was observed. Conclusion 18F-FDG PET/CT may be a sensitive and effective method in determining whether the patients with DM suffered from malignant tumor. © 2020 The Authors.Treatment for mandibular fractures is commonly performed via open reduction fixation with mini titanium or resorbable plates and screws. The investigators hypothesized differences in maximum mechanical stress forces and deflection with each plating material; however, it was proposed that the experimental forces withstood by the resorbable system would be enough to withstand normal forces produced during mastication. Sovleplenib The sample was composed of fresh cadaver mandibles that were harvested, fractured, and fixated with plates and screws. The predictor variable was fracture fixation and included a titanium plating or resorbable poly-L-lactide plating system. The primary outcome measure was maximum load withstood before plating failure measured in Newtons (N). Descriptive and bivariate statistics were computed, P value was set at .05. The sample was composed of six mandibles with and grouped by type of fixation modality, Titanium (T) (n = 3) and Resorbable (n = 3). There was a statistically significant correlation between the T group and increased maximum load (N) before failure as compared to the R group, (P = 0.023). The results suggest that fracture fixation with titanium plates and screws can withstand greater maximum forces before failure; however, the resorbable plating system withstood forces similar to/or greater than the maximum forces produced during normal mastication. © 2020 Published by Elsevier Ltd.The present study assessed the potential use of clearing nut seed powder (Strychnos potatorum) as an adsorbent for the removal of Co(II) ions from aqueous solutions. Based on FTIR analysis, the adsorbent possesses hydroxyl, C-N, and C-O functional groups and SEM analysis indicated the presence of uneven porous surface structure, which is important for adsorption. Batch adsorption studies were performed to investigate the effect of contact time, initial pH, initial Co(II) concentration, adsorbent dosage, and temperature on adsorption. The Langmuir isotherm model provided the best explanation to experimental data with the highest correlation coefficient and the maximum monolayer adsorption capacity obtained was 4.245 mg/g. The pseudo-second-order kinetic model fitted well with the adsorption kinetic data. Sorption thermodynamic data showed that the adsorption process is spontaneous and exothermic in nature. The clearing nut seed powder obtained after surface modification by acid treatment showed a higher adsorption capacity. © 2020 Published by Elsevier Ltd.In binary image segmentation, the choice of the order of the operation sequence may yield to suboptimal results. In this work, we propose to tackle the associated optimization problem via multi-objective approach. Given the original image, in combination with a list of morphological, logical and stacking operations, the goal is to obtain the ideal output at the lowest computational cost. We compared the performance of two Multi-objective Evolutionary Algorithms (MOEAs) the Non-dominated Sorting Genetic Algorithm (NSGA-II) and the Strength Pareto Evolutionary Algorithm 2 (SPEA2). NSGA-II has better results in most cases, but the difference does not reach statistical significance. The results show that the similarity measure and the computational cost are objective functions in conflict, while the number of operations available and type of input images impact on the quality of Pareto set. © 2020 The Authors.